The tyco st-tpr pressure balance type trap


Product features

The control can be adjusted automatically according to the pressure change.
In the machine and normal operation, it has superior emptying performance.
The size has a large displacement relative to its size.
Strong internal design ensures long life.
Pressure range: 450Psi (31 bar)

Firmness: manual can control water hammer and overheat
Reliable and effective operation: low steam flow loss
Freezing: vertical installation or horizontal installation.
Stainless steel structure: can resist internal and external corrosion

Tikko st-dmt bimetal trap

Bimetal sheet trap is the most solid steam trap in the thermostatic type trap.
Its advantages are: not afraid of water hammer, high pressure, small volume, light weight, not afraid of freezing, can automatically exhaust air, any position can be installed;
The back pressure rate is greater than 80 %.
The ST - DMT bimetal trap is suitable for steam pipe main pipe, pipe network with heat, instrument with heat, life heating, and the heating equipment that allows high temperature condensate water, which is widely used.

The performance characteristics of

1. Can adjust the discharge temperature of condensate water and effectively use the heat of the condensation water.

2. Before the valve, there is condensation water, forming water seal, no steam leakage.

3. Install at any Angle and adjust the drainage temperature at any time.

4. Anti-water hammer, excellent exhaust performance.

5. Spherical closed mode, long service life

Tekko st-fft float ball type steam trap

For steam heating equipment, steam pipe network and condensate recovery system, it can eliminate condensate quickly, automatically and continuously, effectively preventing steam leakage

The performance characteristics of

The water trap is widely used
It can work efficiently under low and low condensate load.
The structure is compact.
Continuous discharge and large displacement - ensure the heat transfer effect.
For automatic temperature control equipment, float trap is the best choice.
The standard product has built-in vent valve and can provide broken steam lock device.

Tyco st-ibt inverted bucket steam trap

ST - the IBT inverted bucket type steam trap is the use of condensed water and steam density difference between the working principle of the internal structure consists of lever system connecting the inverted bucket, overcome the steam pressure switch inverted bucket type steam trap is an inverted bucket inside for the liquid level sensitive parts, inverted bucket downwards.
When the device has just started, air and cold condensate will appear in the pipe. At this time, the steam trap valve is fully open, and the air and cold condensate are discharged rapidly, and the device will soon raise the temperature.
When the steam enters the bucket, the bucket produces upward buoyancy, and the bucket connecting lever leads the valve to close the valve.
Open a small hole at the inverted bucket to automatic exhaust air, as part of the steam from a small hole, the other part of the steam condensate, sink down the bucket loses buoyancy and inverted bucket link lever drives the valve core to open the valve.
When the steam is re-entered into the bucket, the valve is closed again, circulating and discontinuous

The performance characteristics of



All moving parts of the inner cavity are stainless steel, wear resistant and corrosion resistant.

The steam does not reach the sealed valve seat, so there is no steam damage
Loss, efficient energy saving.

The tank is inverted, will not be damaged, flat, not afraid of water, long life.

The top of the inverted barrel has a vent.
Continuous air discharge is good, it will not form cold lag and gas blocking.

You can work well under high back pressure without being affected by back pressure.

The work is reliable, only two moving parts (lever - and inverted barrel), so no card resistance will be generated.

The seat and disc are at the top of the valve. The disc can be used in the switch to allow the dirt to pass, with good self-cleaning performance and no dirt.

Tikko st-tds thermal steam trap

The thermal hydrophobic valve combines the characteristics of safety, reliability, simple structure and high efficiency. The maximum working pressure can reach 120 barg.

The performance characteristics of

The structure of the structure is strong, simple, the quantity is light, the operation pressure range is large.
There is only one moving part of a hardened stainless steel disc, which is very
Long service life.
The function of check valve is also available.
The intermittent discharge drainage and rapid close closure ensure no leakage;
Can withstand overheating, water hammer, cold, corrosive condensation water;
The disc falls into the seat with a "click" sound for easy detection
The performance can work under any installation position;
There are various kinds of different models, which can choose thread, flange, welding and so on
way